SKU: OSD-ATM-7
OSD ATM77x Zone Automatic Speaker Selector w/ Remote Control IR Code
New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
Warning: California's Proposition 65
Warning:
This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
- Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
- # of Zones or Speaker Pairs: 7
- Single Source
- Impedance Protection: No
- Maximum Operating Range: 400W
- Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
- Input/ Output Connector Type: Multi-way Binding Posts
- Last Call Back-up Memory Function
- Rack Mountable: Yes, 1.5RU
- Remote Control: Yes
- Dimensions (L x H x D): 16.5" x 3" x 7.87"
- Weight: 7 lbs
- The ATM7 does not have any Internal Impedance Matching Protection
- Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.
- Warranty: 2 Years
Infrared Emitter Information and Installation Guide:
- With 5 meters cable length
- With 3.5mm mono standard plug
- With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
View Owner's Manual
113 Questions asked
Have a Questions?
What's on your mind?
Bruce • 12/17/2019, 2:17:43 PM
I received my ATM-7 on Feb 8th 2012 and the shutting off issues are not fixed..... whats up...how can I get one that works... Thanks
Customer Service • 12/17/2019, 2:17:43 PM
Hi Bruce:
Is the unit still shutting down after 60 seconds, no matter how many speakers are enabled or attached?
TL
Bruce • 12/17/2019, 2:17:43 PM
I received my ATM-7 on Feb 8th 2012 and the shutting off issues are not fixed..... whats up...how can I get one that works... Thanks
Customer Service • 12/17/2019, 2:17:43 PM
Please contact Brennan at brennan@osdaudio.com for an RMA
Bruce • 12/17/2019, 2:17:43 PM
I received my ATM-7 on Feb 8th 2012 and the shutting off issues are not fixed..... whats up...how can I get one that works... Thanks
Customer Service • 12/17/2019, 2:17:43 PM
The unit is working fine now It was my fault . Thanks for your response and concern...
I'm very happy with everything the speakers and the speaker selector. Thanks again...
Dave E • 12/17/2019, 2:17:43 PM
Apparently not all of these have been repaired, I received one 2-17-2012 and it has this issue, what s the fix?
Customer Service • 12/17/2019, 2:17:43 PM
Hi Dave:
Sorry to hear you are still having problems. I believe we will be sending you a new unit that we will run extensive tests to make sure it is not expierencing the same issues.
TL
Kaman • 12/17/2019, 2:17:43 PM
Dear Sir,
I have just received the device, I do not know how to set multizone playing, that is Zone 1 to 4 from source A and zone 5 to 7 from source B. When Both sources are playing, the signals seem to be mixed together and I do not know to the direct one source to specific zones as well.
Kaman
Customer Service • 12/17/2019, 2:17:43 PM
Hi Kaman:
This unit does not allow you to listen to seperate sources at the same time. There is not an independent A B choice per zone. We have that feature on our DSM and SSVC speaker selectors. You can only select source A or Source B for all zones. Note based upon your setup Multi Zone should be enables, The Master Slave switch should be set to off on the back of the unit. You should also have the 2in button pushed. You can then select either Zone A or Zone B which really should be considered Source A or Source B when in the ZONE 2 input mode.
TL