SKU: OSD-ATM-7
OSD ATM77x Zone Automatic Speaker Selector w/ Remote Control IR Code
New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
Warning: California's Proposition 65
Warning:
This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
- Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
- # of Zones or Speaker Pairs: 7
- Single Source
- Impedance Protection: No
- Maximum Operating Range: 400W
- Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
- Input/ Output Connector Type: Multi-way Binding Posts
- Last Call Back-up Memory Function
- Rack Mountable: Yes, 1.5RU
- Remote Control: Yes
- Dimensions (L x H x D): 16.5" x 3" x 7.87"
- Weight: 7 lbs
- The ATM7 does not have any Internal Impedance Matching Protection
- Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.
- Warranty: 2 Years
Infrared Emitter Information and Installation Guide:
- With 5 meters cable length
- With 3.5mm mono standard plug
- With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
View Owner's Manual
113 Questions asked
Have a Questions?
What's on your mind?
Wayne Powell • 12/17/2019, 2:17:43 PM
Hello. I have an older Pioneer Elite VSX-49TX A/V Receiver .I have 6 speaker sets (12 total) that I need to control. I have installed impedance matching volume controls to all speaker zones. My receiver states that speakers should be 6-16 ohms of nominal impedance. Would this unit work for my application ? Thanks.We purchased our speakers and controls mostly from you folks and love them so far.
Wayne
Customer Service • 12/17/2019, 2:17:43 PM
Hi Wayne,
In order to use the ATM-7 speaker selector, you’ll need a separate amplifier like our AMP300 with impedance-matching volume controls.
CL/MA 1717
Roland • 12/17/2019, 2:17:43 PM
Hi, sorry for a beginner question here: I have 8 single speakers - all 8 ohm. I have 1 receiver with 1 available stereo speaker output (receiver can handle down to 4 ohm). Can i connect this stereo speaker cable to the ATM 7 Zone device and then spread to the 8 single speakers ? I am not sure how impedance is managed as it is stated that the device does not manage impedance ? thanks for clarification (to a non-technician..)
Thanks
Roland
Customer Service • 12/17/2019, 2:17:43 PM
Hi Roland,
With the ATM-7 speaker selector, we recommend using an even number of impedance-matching volume controls. If your stereo receiver only has one output left, adding 8 speakers to might be too much. We recommend an additional amplifier like our AMP200 to drive your 8 speakers. Are the speakers placed in a position to be in stereo? The ATM-7 is setup for a left and right speaker per zone. Assuming they are 8-ohm speakers, you have several options but we need to know a little bit more about your setup. Could you provide us with simple diagram? Here is a link to Upload your plans- http://www.outdoorspeakerdepot.com/help-center.html
CL/MA 1730
Derek • 12/17/2019, 2:17:43 PM
I have a Denon AVR-3801. An older unit but heavy duty at that and has been great all around. I would like to run all 7 zones of the ATM-7 off the multizone on the denon. I currently use the mutizone paired with the harmony link and is a breeze to control with my phone. I just want to expand to the whole house and have the ir remote capable switch (ATM-7) to control as well. Would putting in impedance matching controls in all 7 zones and running it off the denon avr-3801 be enough to power all zones or would I need another distribution amp? Or would getting another distribution amp with impedence matching built in bypassing the impedence matching wall controls be more efficient? I really would'nt mind not having wall controls as I can control volume level with my phone anyway just not independently. What is my best option?
Customer Service • 12/17/2019, 2:17:43 PM
Hello Derek,
The ATM-7 speaker selector does not have impedance matching so volume controls will be required. You can use our SVC100s for impedance matching set at 8X. However, the power output of your multi-zone receiver may not have enough power to drive seven pairs of speakers. Consider adding our AMP300 to drive your whole house speakers. We are obtaining the remote code for you from our factory. Please email casey@outdoorspeakerdepot.com for future correspondence.
CL/MA 1782
Michele Palmas • 12/17/2019, 2:17:43 PM
Hi, i'm interested to buy the ATM-7 but I like to ask you some question,
1) it' possible controll the ATM-7 by Logitech Armony link , in mode that I can change the zone by iPhone/iPad?
2) you have some dealer in Europe where I can order the ATM-7?
Thank you, and best regards, Michele
Customer Service • 12/17/2019, 2:17:43 PM
Ciao Michele,
The ATM-7 speaker selector cannot be controlled by iPhone/ iPad. We do not have a dealer in Europe, but we do ship international. You can place an order online and have it delivered to you in Italy.
CL/MA 1872
david • 12/17/2019, 2:17:43 PM
Hi. Will the ATM-7, or any other typical speaker selector work with outside wireless pool speakers?
Customer Service • 12/17/2019, 2:17:43 PM
HI David,
A speaker selector distributes power. You wouldn't need to use it with wireless speakers because they are self-powered. What is the music source you would be using?
CL/MA 1886