SKU: OSD-ATM-7
OSD ATM77x Zone Automatic Speaker Selector w/ Remote Control IR Code
New improved we dim the blue led indicator light so it is not too bright at night. Speaker selector switches allow you to connect multiple pairs of speakers to your stereo receiver or amplifier. The ATM 7-Zone Speaker Selector with Remote Control can control up to seven pairs of speakers so you can listen to music in multiple rooms simultaneously.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
ATM 7-Zone Speaker Selector includes an IR remote control. With a backup memory function and a 10-meter remote operating distance, this may be the perfect solution for your needs. Also you can easily program the remote control to any of your favorite universal remote control with the factory code we provide.
Warning: California's Proposition 65
Warning:
This product can expose you to chemicals, including vinyl chloride, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
- Speaker Selector Type: 7 Zone Speaker Selector w/ IR Remote Control
- # of Zones or Speaker Pairs: 7
- Single Source
- Impedance Protection: No
- Maximum Operating Range: 400W
- Input Source: 7 Inputs to Speaker A/B or 2 Sources to 7 Zones
- Input/ Output Connector Type: Multi-way Binding Posts
- Last Call Back-up Memory Function
- Rack Mountable: Yes, 1.5RU
- Remote Control: Yes
- Dimensions (L x H x D): 16.5" x 3" x 7.87"
- Weight: 7 lbs
- The ATM7 does not have any Internal Impedance Matching Protection
- Note: We recommend adding Impedance Matching Volume Controls for each zone if you are planning to play more than two 8-ohm pairs of speakers at the same time.
- Warranty: 2 Years
Infrared Emitter Information and Installation Guide:
- With 5 meters cable length
- With 3.5mm mono standard plug
- With self-adhesive tape for quick and easy fixing on any hard, clean & dry surface.
View Owner's Manual
113 Questions asked
Have a Questions?
What's on your mind?
Bernard • 12/17/2019, 2:17:43 PM
I just purchased the ATM-7 and AMP300 to use for my home audio system with 7 pairs of wall/ ceiling speakers. All the speakers are wired to a common location, where i will place the amp and speaker selector. Do i need impedance matching volume controls for the speakers? Currently i do not have them. my source is a sonos connect, so i can control the volume thru my ipad. is this going to work okay?
Customer Service • 12/17/2019, 2:17:43 PM
Hi Bernard,
Yes - the ATM-7 doesn't have built-in impedance protection like our other speaker selectors, so you would need to run impedance matching volume controls on each zone to run it safely.
Tom • 12/17/2019, 2:17:43 PM
I have two amps, a marantz sr5006 which has 650 watts and 9 output channels, and a Yamaha rxv777bt which has 805 watts and 7output channels, I have four tower speakers rated to 275 watts and two powered sub woofers.
I want to hook the speakers to a common source and switch between the amps.
Is this a good product for this purpose and are there any concerns?
Thanks
Tom
tgstsevenson@comcast.net
Customer Service • 12/17/2019, 2:17:43 PM
Hi Tom,
Not exactly. Neither of these receivers look like they can handle anything more than 8ohms per output - meaning running a speaker selector would be a unstable load and could damage the receivers. Typically you need to run a speaker selector like this with a high-current amp such as our AMP300. This is our professional advice, however you are free to try running the ATM-7 or a dual source speaker selector with these two receivers if you choose. Essentially the function is what you are looking for, but the question is can they safely run multiple pairs of speakers.
Peter • 12/17/2019, 2:17:43 PM
I have 4 amplifiers, and 3 sets of speakers.
What I am trying to accomplish is to be able to switch any of the amplifiers to any of the speaker pairs, but I am not planning on running multiple amps or running multiple speakers _simultaneously_
For example, i would like to be able to use my tube amplifier with low power output with any speaker set that has a high sensitivity. But those speakers are already connected to another amplifier, so i need to re-cable speakers and tube amplifier. At no point am i trying to run the speaker sets concurrently (like in multiple rooms), i just want to avoid the re-wiring.
Will the ATM-7 work for me ? I do not have a impedance matching control but can i go without if only powering up one set of speakers at any given time ?
Thanks in advance.
Customer Service • 12/17/2019, 2:17:43 PM
Hi Peter,
The ATM-7 can either be run using the 7 zones for speakers and the 2 source inputs for amps or vice versa, using the zones for your amps and the sources for your speakers.
ENELSON • 12/17/2019, 2:17:43 PM
Hello, I bought 2 pairs OSD-ACE 540, 1 pair of OSD-ICE640, 1 pair of RC65i In-wall Loudspeaker from Polk Audio and 2 pairs of rc85i and 5 OSD-SVC205 (all installed and operating). I have a STR-DN1030 SONY and now I would like to use an ATM-7 (purchased), how do I connect the ATM-7 on the Receiver? Even having bought and installed the OSD-SVC205, can i install ATM-7? I need to buy a AMP300? Thanks!
Customer Service • 12/17/2019, 2:17:43 PM
Hello,
It would be very risky trying to run that many speakers off a standard receiver. I recommend going with our AMP300 so you don't risk damaging your components. Run a 4-conductor speakers wire from the amp to the ATM-7.
james • 12/17/2019, 2:17:43 PM
I have a Integra DTR-7.8 AVR. I was wondering if I can connect my powered zone 2 into this unit to power 3 pair of speakers? Thanks for your help and time. james
Customer Service • 12/17/2019, 2:17:43 PM
Hi James,
It's not recommended as receivers such as yours can typically only run at 8ohms (1 pair of speakers). Running a multi-zone speaker selector will create an unstable load and you run the risk of damaging your receiver. Best to run an AMP300 to the ATM-7.